Information

Potentiostat|Galvanostat

Model : ZIVE BP2C
Company : WonATech
Country : South Korea

ZIVE BP2C , the dual channel potentiostat / galvanostat /ZRA/FRA, is to support dual working electrodes cell with one reference and one counter electrode configuration ( bi-potentiostat).

Introduction

The ZIVE BP2C, a dual channel potentiostat/galvanostat/FRA, is to support dual-working-electrode cell with one reference and one counter electrode configuration(bi-potentiostat) for sample characterization. Each channel can conduct DC and impedance test simultaneously and/or independently. The ZIVE BP2C can be setup to run 2-electrode, 3-electrode, or 4-electrode measurements with a simple setup change.

The ZIVE BP2C’s each channel is equipped with a frequency response analyzer(FRA) as standard and it provides high performance impedance measurements over the frequency range 10uHz to 1MHz. ZRA(zero resistance ammeter) function can measure max. 2 Amp in galvanic corrosion technique. The system is supplied with four(4) advanced software packages, which are catagorized by application fields. With this advanced software packages, user can widen ZIVE BP2C’s flexibility.

features

Features System

Versatile high quality dual channel potentiostat/galvanostat/impedance analyzer
Bi-potentiostat

two fully independent channels
dual working electrodes with one reference and one counter electrode
configuration available

FRA function to control an external electronic load or 3rd party potentiostat/galvanostat is available as standard
14 EIS techniques capability including multisine
Current interrupt IR measurement IR compensation(dynamic, positive feedback)
Bipolar pulse capability
Voltage pulse or current pulse charge/discharge test(GSM,CDMA etc.), sine wave function for ripple simulation in battery test package and pulse plating available
High speed data sampling time per channel

50usec/sample in burst mode
1msec/sample in normal mode
2usec/sample in fast sweep mode

Fast sweep mode(5000V/sec with 10mV data sampling)
3 measurement/control voltage ranges & 12 measurement/control current ranges

Application

Application:

The ZIVE BP2C, a dual channel electrochemical workstation is ideal for bio sensor research, FET sensor, permeation test etc. And it can be also used for fundamental research in electrochemistry, development and quality assurance of new sensors, corrosion/ coatings, electrode material, membrane, conducting polymer, evaluation power device research such as battery materials, fuel cells, super capacitors and solar cells.

Specification

Specificaton:

Main system
PC communication	USB2.0 High Speed
Line voltage	100-240VAC, 50/60Hz, 1Amp
Max. channel number	2 independent channels per unit
Size/weight	209X270X378mm(WxHxD) / 9.25kg
Max output power	30Watt
System
Cell cable	1meter shielded type (Standard)
	Working, reference, counter,
	Working sense
Control	DSP with FPGA
Calibration	Automatic
Data acquisition	2x16bit ADCs (500kHz)for voltage, current
ADC	4x 16bit ADCs(250kHz) for auxiliary voltage & temperature reading
DAC	2x16bit DAC(50MHz) for bias & scan
DAC	1X16bit DAC(1MHz) for analog output
Filter	4ea (5Hz,1kHz,500kHz, 5MHz)
Scan rate	0 – 200V/sec 0-5000V/sec(fast scan)
Max. channel No.	32 Channels via USB connection
Internal Data Memory	295,000 points
LCD Display	DC & EIS mode automatically
Power amplifier(CE)
Power	24Watt (12V@2A)
Compliance voltage	±12V
Maximum current	±2A
Control speed selection	8ea
bandwidth	5MHz
Slew rate	10V/usec
Potentiostat mode(voltage control)
- voltage control
Control voltage range	±10V, ±1V, ±100mV
Voltage resolution	16 bit per each range
Voltage accuracy	±1mV±0.05% of setting
Max. scan range	±10V vs. ref. E
- current measurement
Current ranges	12 ranges(auto/manual setting)
	20pA ~ 2A
	(20pA & 200pA with gain)
Current resolution	16 bit;
	60uA,6uA,600nA,60nA,6nA,600pA,
	60pA,6pA, 600fA, 60fA,6fA,0.6fA
Current accuracy	±10pA±0.1% of range(gain x1) >200nA fs
Galvanostat mode(current control)
- Current control
Control current range	Max. ±2A
Control current range	± full scale depending on selected range
Current resolution	16 bit;
	60uA,6uA,600nA,60nA,6nA,600pA,
	60pA,6pA, 600fA, 60fA,6fA,0.6fA

Current accuracy	±10pA±0.1% of range(gain x1) >200nA fs
- Voltage measurement
Voltage ranges	10V,1V,100mV
Voltage resolution	16 bit; 0.3mV,30uV,3uV
Voltage accuracy	±1mV±0.05% of reading
Electrometer
Max input voltage	±10V
Input impedance	2x10¹³¥Ø\|\|4.5pF
Input impedance	2x10¹³¥Ø\|\|4.5pF
Bandwidth	>22MHz
CMRR	>114db
EIS(Internal FRA) for system
Frequency range	10uHz ~ 2MHz
Frequency accuracy	0.01%
Frequency resolution	5000/decade
Amplitude	0.1mV ~ 5V rms (Potentiostatic)
Amplitude	0.1 ~ 70% f.s(Galvanostatic)
Mode	Static EIS:
	Potentiostatic, galvanostatic, pseudo-galvanostatic, OCP
	Dynamic EIS:
	Potentiodynamic, Galvanodynamic
	Fixed frequency Impedance:
	Potentiostatic, Galvanostatic, potentiodynamic, galvanodynamic
	Multisine EIS:
	Potentiostatic, Galvanostatic
	Intermittent PEIS/GEIS¡¡
Interfaces for system
Auxiliary port
Digital output	3 (open collector)
Digital input	2 (photo coupler)
Auxiliary voltage inputs	3 analog Inputs: ±10V
	For measurement of WE vs. CE
	CE vs. RE or other signal
Analog output	1 analog output: ±10V
	For stirrer, MFC, RDE etc.
Misc. port
Sig generator output	1 analog output for FRA output or
	waveform generation output
Peripheral communication	I2C to control external devices

Temperature measurement	1 K-type thermocouple input
Zero Resistance Ammeter	2nA ~ 2A ranges
Software
Max steps per experiment	1000
Shutdown safety limits	Voltage, current, temperature etc
Max. sampling rate	20kHz(50usec)-burst mode/500jHz(2usec) in fast sweep mode
Max. sampling time	unlimited
Sampling condition	Time, dv/dt, dI/dt, temp etc.
PC requirement
Operating system	WindowsXP SP3/7/8/10
PC specification(minimum)	Pentium4, RAM 1GB
Display	1600x900 high color
USB	High speed 2.0
General
Dummy cell	One external dummy cell included
Thermocouple	1.5meter K-type (option)
Auxiliary cable	Option
Misc. cable	Option

Potentiostat| Galvanostat

Information